How Much Does Landscape Edging Cost in 2026?

Prices have shifted the past couple of seasons, and you want straight talk before you trench a line around your lawn or garden. Here's a clear look at landscape edging cost for 2026, from cost per foot to real project totals. You'll see how steel garden edging compares with concrete, brick, and plastic, plus what affects the price in our rocky soils and freeze–thaw swings.

 

Average Cost Per Linear Foot and Typical Project Totals

Most landscape edging cost ranges follow a simple pattern. Across the United States, the typical landscape edging cost per foot runs $3.50 to $11.50 installed, depending on the material and the amount of prep the site needs. Plastic stays near the low end, while brick, stone, concrete, and metal can increase the price.

Here is what most projects fall into:

• Small projects (30 to 80 feet) usually range from $100 to $900
• Average yards (100 to 200 feet) often land between $350 and $2,300
• Large runs (300 to 1,000+ feet) can range from $600 to $11,500+

These totals include the cost of materials, trenching, staking, and basic cleanup. Curves, slopes, soil, and access can move the landscape curbing cost up or down, but most jobs stay close to these ranges.

Note: These numbers reflect general industry averages. Prices can shift during the year as fuel and material costs change, so getting an updated quote is still the best way to plan your budget.

What's Included In A Standard Install

Most landscape edging services follow the same basic steps. A typical install includes layout, light sod cutting, trenching, preparing the base, setting and staking the material, backfilling, compacting the soil, and cleaning up the area. These steps help keep the edge straight and prevent shifting over time.

Some tasks can raise the final cost. These include working through heavy rock or roots, hauling extra soil, saw cutting near a driveway, repairing irrigation lines, adding landscape fabric, or shaping tight curves that take more time to set.

 

Cost By Material

Material choice sets most of your budget. Here's how the big options pencil out.

Steel And Metal Edging

Metal landscape edging is a strong choice when you want clean, straight lines that stay in place. Material cost usually ranges from $2 to $10 per foot, depending on the gauge and finish. Installed cost often falls between $10 and $28 per foot, with thicker steel garden edging sitting at the higher end. A common example is a 6-inch 14GA galvanized roll-top steel edging, which is often used when a project needs more strength and depth.

Steel handles curves well, stays low enough for mowing, and stays steady when pinned correctly. Galvanized or coated options help keep the color steady, while raw steel develops a natural patina over time.

Concrete Curbing

Concrete curbing forms a continuous border around lawns, driveways, and garden beds. Most concrete landscape curbing cost ranges stay between $14 and $28 per foot, while stamped or colored concrete often runs $20 to $40 per foot. These prices cover both materials and labor.

Concrete gives a clean, finished border and helps separate mulch, soil, and grass. A solid base and spaced joints help prevent cracking. It can chip at corners, but small repairs are simple.

Natural Stone Or Boulder

Stone edging brings a natural look that blends well with many lawn and garden designs. Material cost often ranges from $12 to $35 per foot, and larger stone or boulders cost more due to handling. Installed cost usually lands between $25 and $60 per foot, depending on weight and the time needed to set each piece. Some projects use shaped stone pieces like Edgestone edging for a cleaner, easy-to-place border.

Stone can also act as a light retaining edge on gentle slopes. It lasts a long time, although stones can shift if the base is not compacted well.

Brick Or Paver Edging

Brick and paver edging gives yards a clean, classic border that pairs well with patios and walkways. Material cost usually ranges from $6 to $14 per foot, depending on the pattern and the type of paver. Installed cost often falls between $18 and $38 per foot for a simple soldier course, with more detailed cuts increasing the price. A strong base and a good paver edging restraint help keep the line straight and prevent bricks from shifting.

Brick and paver edges allow easy spot repairs and come in many colors. The joints may need sand or occasional touchups to keep weeds from moving in.

Plastic, Composite, and Rubber

Plastic, composite, and rubber edging offer a low cost landscape edging choice for quick garden and lawn borders. Plastic material cost often ranges from $0.80 to $2 per foot, and installed cost stays near $5 to $12 per foot. Composite or rubber edging usually runs $3 to $6 per foot for materials and $8 to $16 per foot installed. Lightweight options like Slim-Edg plastic edging help create simple curves and are easy to shape for DIY projects.

These materials work well for small beds and fast installs. They can lift over time in cold climates, so staking and smooth soil contact help keep the line steady.

Wood Timbers

Wood timbers give a warm, rustic edge around garden beds, gravel areas, or play spaces. A typical timber costs $15 to $35 per piece, and the installed cost often falls between $10 and $22 per foot, depending on the size and how much base prep is needed. Treated wood handles soil and moisture better and lasts longer in sunny areas.

Wood offers a simple, natural look, but corners can loosen over time and the material can weather faster than metal or concrete. It works best in low-traffic areas or where you want a softer border.

 

Labor and DIY Vs. Pro

Here's how to think about doing it yourself or hiring a crew.

When DIY Works And When To Hire

DIY fits straight runs with plastic, composite, or standard metal strips when you have decent soil and easy access. You will spend more time on base prep and staking but save on labor. Having basic hand tools and a few striking tools can help keep the line steady.

Bring in a pro when you want continuous concrete curb, long runs of steel garden edging with tight curves, or you are working through heavy rock, roots, or irrigation. If the edging ties into a retaining wall, patio, or driveway, a pro can help keep grades and drainage correct.

Mobilization, Access, And Equipment

Mobilization often adds a small cost for travel and loading equipment. Crew rates vary and may include the use of sod cutters, trenchers, plate compactors, or a curb machine. Access can raise labor time when yards are narrow, uphill, or require debris hauling.

 

Local Factors That Move The Price

Our soils and weather add a few twists to the budget. Plan for these.

Rocky Soils and Trenching Depth

Rocky ground slows trenching and can bend lighter edging. Crews may swap to heavier steel or add more pins, which raises landscape edging prices. Deeper trenching for metal or a thicker base under pavers can also nudge the cost per foot.

Freeze–Thaw, Frost Heave, and Anchoring

Cold weather and frost movement can shift edging if the base is weak. Proper base prep, more frequent stakes, and deeper anchors help keep a curb line straight. Concrete curb needs good subgrade and control joints. Steel often uses longer spikes at 18 to 24 inches on center. These steps add a little to the price but help reduce future fixes.

Slopes, Drainage, and Irrigation Lines

On slopes, edging sometimes acts as a mini check for mulch, which may need better base compaction, extra pins, or step-downs. If drainage upgrades or a swale are needed, costs rise. Mapping irrigation before trenching helps avoid repairs. If a line is nicked, expect a small service charge. The soil and materials around the base of the house can also influence how the layout is shaped.

Curves, Radii, and Transitions

Tight radii need more cuts in brick or pavers and more stakes in metal. Transitions at a driveway or a path take extra detail work to keep the mower edge clean. These details add labor minutes that can add up over 100 to 200 feet.

 

Longevity, Maintenance, and Value Over Time

Looking past the install price helps you pick what lasts in our climate.

Lifespan By Material In A High-Temperature-Swing Climate

• Steel and metal edging: 15 to 25 years, longer for galvanized or powder-coated. Occasional touch-up on scratches helps.
• Concrete curbing: 15 to 30 years with good base and joints. Sealer can add life and color hold.
• Natural stone or boulder: Often lasts for decades with solid base prep and drainage.
• Brick or paver edging: 10 to 20 years depending on base, restraint, and traffic.
• Plastic: 5 to 10 years. Composite or rubber: 10 to 15 years.
• Wood timbers: About 5 to 10 years in sunny areas or where irrigation hits regularly.

Maintenance And Repair Costs To Plan For

• Steel: Extra spikes or resetting a section are common and usually a small service visit. Touch-up paint for coated steel is inexpensive.
• Concrete curb: Crack repair or corner patch often costs between $150 and $400 for a small fix. Resealing color adds a small cost every few years.
• Brick or pavers: Re-leveling and adding joint sand are the most common needs. Materials are low cost, labor is the main factor. Good joint sand and adding a mulch also help manage weed growth around the edge.
• Stone: A piece may need to be reset if it shifts during winter.
• Plastic: Lifted sections may need more anchors or replacement. Material is low cost but adjustments can be more frequent.

Smart Ways To Save Without Regretting It

• Keep lines simple. Fewer tight curves lower labor and waste.
• Prep what you can: mark utilities, move decor and pots, and stage materials close to the work.
• Group work. Team up with a neighbor to share mobilization and disposal costs.
• Pick standard finishes. Standard steel or uncolored curb costs less than custom coatings or stamps.
• Match material to the use. Steel or concrete near a driveway edge holds up better than plastic, which saves repair calls later.
• Buy once, cry once. Low cost landscape edging can look good day one but cost more in resets and replacements.

 

Get Your Yard Ready With Reliable Edging Supplies

Landscape edging cost changes based on the material, the length of the run, and how much prep the site needs. Steel garden edging, concrete curb, brick, and stone offer strong, long-lasting borders, while plastic and wood keep the upfront price low. A clear layout, the right base, and good drainage help the edging stay straight and protect your lawn and garden over time.

Rivendell Distribution offers edging materials, soils, and tools that support both DIY work and larger installs. You can order online anytime or stop by 3961 County Road 114, Glenwood Springs, CO to see materials in person and choose what fits your project.

 

Landscape Edging Cost FAQs

What is the average landscape edging cost per foot on Colorado’s Western Slope in 2025?

Installed landscape edging cost usually runs $8–$28 per linear foot. Small projects (30–80 ft) sit around $300–$2,000, average yards (100–200 ft) fall between $1,200–$5,000, and large or commercial sites (300–1,000+ ft) reach $4,500–$30,000+. Pricing follows material and fuel costs, so a fresh 2025 quote is the safest way to confirm numbers.

How do steel garden edging and concrete curbing compare on cost and performance?

Residential steel edging often installs at $10–$22/ft, while thicker steel runs $15–$28. Concrete curbing typically costs $14–$28/ft, with stamped or colored styles at $20–$40. Steel gives a clean, low-profile border that handles rocky soil well. Concrete offers a continuous curb, solid weed separation, and smooth curves when the base and joints are done correctly.

What local factors most affect landscape edging cost on the Western Slope?

Material choice drives most of the cost, but labor and terrain play a big role. Rocky soils slow trenching and often need heavier steel or extra anchors. Freeze–thaw cycles push crews to improve base prep. Slopes, drainage adjustments, curves, and irrigation line repairs add labor time. For local residential or commercial projects, you can always contact us to compare materials and get practical advice for your site.

When is the best time of year to install landscape edging in Colorado’s Western Slope?

Spring and early fall are the smoothest times because the soil is workable and temperatures are more stable. Concrete curbing cures best above 40–50°F. Avoid periods when the ground is saturated, thawing, or frozen. Summer installs still work, but crews may need extra dust control and water to prevent cracking or uneven settlement. If you want a simple guide to structure and layout, the principles of landscape design can give helpful context.

Do I need a permit for landscape edging or concrete curbing?

Most steel, brick, plastic, or concrete edging does not need a building permit. Permits may come into play only when tying into public sidewalks or driveway aprons, altering drainage, or working within the right-of-way. It’s always good to confirm with your local city office or HOA before scheduling, especially for concrete near streets or shared access points.